| Customization: | Available |
|---|---|
| Feature: | Environmental, Fireproof, Light Weight |
| Fire Rating: | 4 |
|
Still deciding? Get samples of US$ 0/Piece
Request Sample
|
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
Sound Insulation Board EPS Cement Sandwich Panels for Shopping Mall/Shopping Plaza
Introduction of EPS Cement Sandwich Panels
Lightweight Sandwich Panel is a kind of lightweight Energy-saving wall material taking reinforced calcium silicate or cement calcium silicate Board as face panel,cement,eps,fly ash as core forming by one time compound.
The Lightweight Sandwich Panels has solid, lightweight, thin, better strength, impact resistance, strong hanging strength, heat insulation, sound insulation, fireproof, waterproof, easy cutting, increasing available space. It can be arbitrary slotting, dry operation, environment protection. Which achieve energy conservation and energy efficiency. At the same time,this reduces the total area to be occupied by the wall and to raise residential practical area, alleviates the structure load, improves the building aseismatic capacity and safety performance, and reduce total cost. This production technology and application is the reform of our country wall material, is a new breakthrough.
Features of EPS Cement Sandwich Panels
Waterproof wall
The EPS Cement Sandwich Panels Has Good Waterproof And Moisture-Proof Performance, And Can Be Used In Wet Areas Such As Kitchens, Bathrooms, Basements, Etc. Therefore, The Wall Does Not Loosen, Return To Halogen, Deform, And Reduce Strength Due To Moisture Absorption. Experiments Have Shown That The Wall Panel Can Be Filled With Water Without Any Finish, And The Back Of The Wall Panel Can Be Kept Dry Without Leaving Any Traces. In The Wet Weather, The Wall Will Not Condense, Water Drops, And The General Masonry Can Not Be Damp-Proof. After A Long Time, The Phenomenon Of Peeling Off The Layers Will Occur.
Fire resistant material
Control the fire in the initial unit to prevent the fire from spreading, block the generation of toxic gases (or effectively isolate them), and allow personnel to have enough time to evacuate and extinguish the fire to avoid major loss of life and property. It is a basic fire prevention theory. The non-combustible performance of the EPS cement sandwich panel meets the national Class A standard. After the wall is installed, it has superior stability and integrity, and has good fire resistance. It can limit the fire and smoke gas to the fired area, and does not emit toxic gases. The EPS cement sandwich panel has passed the international SGS and TUV double certification, which effectively proves the fireproof performance of the wallboard. The 100mm thick EPS cement sandwich panel can achieve more than three hours of fire protection, which can greatly protect the safety of life and property.
Application of EPS Cement Sandwich Panels
|
ITEM |
Specification |
|
Length |
2270/2440mm |
|
Width |
610mm |
|
Thickness
|
60mm roof system 75mm roof system 90mm interior partition wall 100mm interior partition wall 120mm exterior wall, floor, roof deck 150mm exterior wall |
Installation of EPS Cement Sandwich Panels
1. Setting the line and carrying the board into position.
2. Using a hand-hold electric saw cut to the sizes needed.
3. Sizing cement on tenon side of two boards, then spread specific mortar on one tenon side casually.
4. Carrying the board prepared to be installed to the installation place, correcting the wall board by
special tools, and making it close tightly. Then let the specific mortar squeeze out into full and then fixing it
with a wedge temporarily.
5. Planting bars in wall and pillar: drill a hole in the original pillar or wall, and fix the board by steel bars
6. Correcting and fixing: Using a guiding rule to check the vertical and leveling correction.
7.Planting bars in structure beam: drill a hole in structure beam and plant a reversed 7-shaped steel bar to fix with wall board.
8. Planting bars in floor: drill a hole in the floor and plant a 7-shaped steel bar to fix with wall board.
9. Planting bars between two boards, plant a steel bar in the angle of 45 degree to fix.
10. Installing electrical wires and switches: setting lines on the places needing to be set with concealed
wire and switch box.
11. Grouting and filling starch: filling and sticking the corrected wall board with polymer mortar.
12. Sticking anti-cracking tape.
After the mortar and wall are all shaped, sticking glass-cloth or anti-cracking tape, brushing coating.
Contact Freda
Freda Lin
Xiamen ZhongJingTai Building Materials Co,. Ltd
Website: http://zjteps.en.made-in-china.com
Tel:0086 136 6600 3756
){kind=link}